In this power, the server is running FreeBSD 10.3. I am completely and unreasonably biased: ZFS is the best filesystem out there. Do not take my word for it. Ask around. Today, I started a process I’ve been waiting to do for a while. I am replacing the 3TB drives in a 10-drive raidz2 array […]
Swapping 5TB in, 3TB out Read More »
I have recently added two 480 GB SSDs to a 10 x HDD raidz2 system. The SSDs will be mainly used for spooling to tape during backups, but I’m going to use a small part of it for a SLOG. Not all systems benefits from a SLOG (Separate intent LOG), but synchronous writes, such as
Adding SLOG to a zpool Read More »
In this post, I am working with FreeBSD 10.2 on this server. Over the past few days, a 3 year old drive has been giving errors. The number of errors has been constant, but I have a spare drive here, so I decided to replace it. I have verified that it is out of warranty.
Added new drive when existing one gave errors, then zpool replace Read More »
I’m using FreeBSD 10.2-RC2 here, with a bunch of HDD. Here are the current pools: The degraded music pool contains a drive I will be replacing later in this post. But first, I want to replace a mis-matched drive in the benchmarking pool. I noticed that when I saw this output: The serial number on
Swapping disks in a zpool Read More »
I’m using FreeBSD 10.2-RC2. One of my new hard 3TB drives was acting up. I removed it and sent it off to be replaced. In the meantime, I received some 5TB drives and I added one of them into the existing vdev of the zpool. First, I partitioned the drive much like the other drives
Replacing a failed drive in ZFS on FreeBSD Read More »
I haven’t tested this yet, but I’ve installed the hardware. The real test will come after a reboot and actual use of the new drives. NOTE: Although this claims to be creating a new ZIL (SLOG) do not believe it. In fact, stop reading right here. There is nothing of use below. What will they
Adding two new drives (SSD) to an existing ZFS system Read More »
THe last system I set up with ZFS, I used a script. Today, when trying a system with different device types, I encountered a limitation of that script. I need to fix it. In the above script, NUM takes on the value of what digits appear in the string of I. Given that DISKS contains
Problem with disk numbering in my ZFS creation script Read More »
I’m getting very slow throughput on these drives during my first set of tests. I have no idea why… The drive in question is: $ grep ada2 /var/run/dmesg.boot ada2 at ahcich4 bus 0 scbus5 target 0 lun 0 ada2: <ST2000DM001-1CH164 CC24> ATA-8 SATA 3.x device ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada2: Command
Testing the benchmark scripts – 1 Read More »
This is a repeat of a benchmark I did yesterday. The drive is a TOSHIBA DT01ACA300 3TB HDD. This is a 7200 RPM SATA III drive. Tests were run with FreeBSD 9.1 in the hardware listed below. Tonight, we’re going to do the partitions slightly differently, and try ZFS. The hardware We are testing on
Benchmarking the TOSHIBA DT01ACA300 – ZFS Read More »
Following on from yesterday’s benchmark, I’m adding in some ZFS tests. All hardware is the same. Of note: $ zdb | grep ashift ashift: 9 $ sudo diskinfo -v ada0 Password: ada0 512 # sectorsize 128035676160 # mediasize in bytes (119G) 250069680 # mediasize in sectors 0 # stripesize 0 # stripeoffset 248085 # Cylinders
Benchmarking the Samsung SSD 840 PRO Series DXM03B0Q – ZFS Read More »